Otto Ganter GmbH & Co. KG
About us
Ganter is at the leading edge in the development, production and marketing of Standard Parts for the entire industry. Quality and volume of production selection set the standards across all ndustries. Ganter’s Standard Parts are offered worldwide through an efficient sales network.
Quality, advice and availability are thus guaranteed – wherever you are located.
Products & services
Mounting clamps with high retaining power
Ganter expands its ball joint selection to include angled and axial ball joints.
For the perfect edge
Ganter completes it's edge protection range with seal profiles with premade 90° corners.
Hygienic Design for Standard Parts
Ganter develops sealed standard stainless steel elements that meet stringent hygiene requirements. Maximum hygiene is one of the absolutely basic prerequisites wherever food is produced. However, hygiene also plays a major role in other sectors — from medical technology and the pharmaceutical industry to manufacturers of dispersion paints. Today, it is all about producing products without preservative additives — and this is only possible in production environments which have high purity levels. Since even the tiniest weak points can cause entire production lines to be contaminated, Ganter decided to develop a special series of standard parts that meet the very high EHEDG requirements and the 3-A Sanitary Standard. Ganter offers a variety of knobs, handles, clamping levers, leveling feet and screws under the label "Hygienic Design", all of which are optimized for minimal contamination and easy cleaning. Stainless steel — with either ground or polished surfaces — is the material used in all of these cases. The maximum surface roughness is kept below Ra 0.8 μm, so that dirt particles cannot adhere and can be reliably removed during cleaning. Another key feature of the Ganter standard parts is their freedom from "dead space". There are no interior areas in which substances can accumulate. A hygienically safe sealing concept, verified by software simulation, guarantees that the FDA-compliant elastomer seals are all installed flush with the surface and fulfill their function in the long term. This prevents problems from developing without being noticed. At first glance, most standard parts appear to be located far away from the actual work areas, but airborne spores from microorganisms can spread rapidly and widely. You can find more information online at www.ganternorm.com
Toggle clamp product range expanded
Latch-type toggle clamps, such as vertical and horizontal acting toggle clamps, have been a permanent feature of the Ganter product range for over 30 years. The expansion of both toggle clamp genres make them the ideal solution for an even wider range of applications. Safety hooks keep the toggle clamp closed securely GN 820.3 horizontal acting toggle clamps and GN 851.3 and GN 852.3 latch type toggle clamps provide a new function: an additional lock prevents inadvertent detachment caused, for example, by vibrations or incorrect operation. When the toggle clamp is closed, the additional safety hook automatically locks and holds the lever in a closed position. The spanner can then be opened, or rather, detached through a simple one-hand operation. The safety hook on the horizontal acting toggle clamps is operated by the index finger, while for the latch type toggle clamps it is opened by pressing from above with the thumb. Now including spindle assembly with rubber tip As previously, Ganter’s horizontal and vertical acting toggle clamps leave no wish unfulfilled: we offer horizontal or vertical mounting bases, as an assembly kit or as a U-bar or solid bar versions. These components have long served as reliable standard parts. The possibility of including an adjustable spindle with a rubber tip is a new option. Until now, these had to be ordered separately as an accessory, for example as the GN 708.1 standard part. The spindle assemblies included in the set correspond to the standard sizes most commonly used – should a specific configuration be required, this can of course be ordered separately. Along with the toggle clamp versions with additional locking as described above, spindle assemblies are also available for GN 810 (vertical acting toggle clamps), GN 812 (with dual flanged mounting base), GN 820 (horizontal acting toggle clamps), as well as for the GN 860 (pneumatically operated spanner) models. Find out more at www.ganter-griff.com
Special solution becomes standard
When it comes to cam action indexing plungers, Ganter offers something very special: the new cam action indexing plungers from the GN 721 series with stop for left- or right-handed operation available with optional locking function. Admittedly, Ganter already offers a very wide range of cam action indexing plungers. Yet frequent inquiries from customers for special designs prompted the company to add another standard part to its extensive standard product range. More specifically, the cam action indexing plungers from the GN 721 series differ in that they limit the range of action to 180 degrees and offer the option of left- or right-hand lock. This allows multi-lock applications to be created with the same direction of movement, and therefore easier handling of valves or other components. In principle, the curve transforms the 180 degree rotation of the lock into an axial lift. If the spring-loaded lock does not unintentionally snap back from this end position, other optional designs with reliable lock notch are available. Also optional: the lock nut pursuant to ISO 8675, which counters the cam action indexing plunger that can be mounted via the external thread in a specific assembly position, and thus guarantees a defined, construction-related locking position. In addition to the normal steel design, the cam action indexing plunger is also available in stainless steel. In both material versions, the lock is available with and without polyamide valve. Other customer-specific special solutions are also possible—for example, cam action indexing plungers with different curve slopes, smaller swivel ranges, special geometries, with a center position or specific locking ranges. More information can be found at www.ganter-griff.com.
Hinges with safety switch in sophisticated design and with unique function!
GN 139.1 hinges with safety switch are used for hinged and opening protective equipment such as doors or covers on machines, in plants, in automation engineering and in the automobile industry. The hinge is compact and sturdy, making it the ideal choice for many applications. Classed as protective equipment, GN 139.1 hinges with safety switch can prevent hazardous situations as the contacts change their status from a defined opening angle forward. This switching point can be adjusted within the range +4°. The electrical switching elements are fully integrated in the mechanical hinge and are invisible from the outside, allowing the hinges to be classed under IP 67 (plug-type version) and IP 69K (cable version). Two contact switches offer double safety! The concealed bolt attachment from the back also makes this hinge particularly tamper-proof. The GN 139.2 hinges are similar in design and differ externally only by featuring a connector plug, making them the ideal choice as add-on hinge with unchanged perfect appearance. Flat and angled mounting plates are available to mount the hinges, allowing them to be mounted from the front or in the clearance between door frame and door. Oblong holes are designed for mounting to profile systems. In general, the GN 139.1 hinges with safety switch conform to many international standards and directives.
Opening and closing – with specialty hinges from Ganter
From simple hinges for welding on to multi-joint hinges with complex kinematics, the Ganter selection has everything needed for superior door and flap solutions – including extra functions. You might think that when it comes to opening and closing, all the possibilities of hinges have already been exhausted. Not even close. Ganter regularly succeeds in making further improvements to hinges, adding practical extra features or creating designs for very particular niche applications.
Highly Secure Connection
Lockable standard parts are increasingly common in machine and plant construction, but they are also used in event hardware for locking and securing a variety of parts. Ganter is now expanding its range of indexing elements to include the lockable stainless steel indexing plungers GN 814. The integrated closing mechanism protects against unauthorized or accidental operation. Lockable indexing plungers GN 814 of stainless steel have the same basic functions as Ganter’s tried and tested selection of indexing plungers. What’s new is the clever addition of a locking function for greater safety and security. This is accomplished with a lock integrated into the black plastic head. On types A and AK, the plunger pin is secured in the front position by turning the key 180 degrees and removing it. The plunger then cannot be moved out of the base position. On types E and EK, the plunger pin can additionally be secured in the rear position, offering a lockable way to prevent the plunger from engaging, which is useful in situations where the plunger pin must be kept from protruding at times. On all types, the key can also be pulled out in the unlocked position to prevent unauthorized locking. The stainless steel indexing plunger is available with two different lock versions: Lock type SC allows all indexing plungers in use to be operated with the same key, while lock type SU requires a different key for each indexing plunger. To prevent unauthorized disassembly or adjustment of the indexing plunger, the hex nut used for screwing the part in or out is only accessible while it is unlocked and the head has been pulled back. A lock nut is available as an optional accessory that can be ordered with the type designations AK or EK with the appended “K” signifying a lock nut.
Long-Lasting and Exact: Pneumatic Clamps from Ganter
Pneumatic clamps are standard elements in jig construction, and Ganter has carried these important fastening systems in its portfolio for some time. The product family has now been reworked – primarily to increase its lifespan and reliability. The most significant improvement concerns the pneumatic cylinder, which now operates with a magnetic piston and has T-slots on the housing. Thanks to this slot, it is now much easier to attach sensors, while the magnetic piston permits more precise querying of the current position by the new, modern sensor GN 3380, which entirely replaces the previous sensors. Of course, other sensors can also be precisely installed in the slot. The pneumatic clamps of the GN 860 series now have hardened, ground bearing bushings and tempered bearing pins for significantly reduced wear. No meaningful alterations were observed in testing for over 250,000 cycles. Structural reinforcement of the sheet steel housing reduces wear-inducing vibrations during operation, which makes a difference even under lower loads. And, finally, the new one-way restrictor in the cylinder enables smoother travel to extend the lifespan of the piston. For high retaining forces, such as are required in car body manufacturing or in pressing or welding lines, Ganter provides the pneumatically operated power clamps of the family GN 864. As part of its optimization strategy, Ganter has made two valuable improvements here. The housings of the standard versions are no longer blackened; they are chemically nickel-plated instead, which considerably increases the corrosion resistance. The FG type is designed specially for welding jigs: The PTFE coating in a characteristic green color prevents weld spatter from sticking – a useful addition to the optionally available protective covers, which ensure long-lasting operation even in aggressive environments. More information on Ganter standard parts can be found on the internet at www.ganternorm.com
Linear actuator connector configured online
Ganter is repositioning itself for linear actuator connectors and will soon beoffering connectors with individual specifications. The real-time online configurator makes this possible. Linear actuator connectors have more different parameters than Ganter‘s Standard Parts strategy could cover — until now. The market leader in standard parts is now presenting a completely new concept that combines the benefits of Standard Parts with a wide range of customization options. This customer-centric strategy is made possible by the new online configurator, which can be used to specify the central parameters of a linear actuator connector and output them in real time. The online configurator offers several advantages over the previous standard offering. In addition to the customizability, it makes the ordering process more efficient because the system immediately checks the selection for plausibility and indicates weight, price and delivery time in real time. The latter takes slightly longer than when ordering standard linear actuator connector, but the ability to enter individual specifications should outweigh this by far. Simultaneous transfer of options into 3D data sets enables the customer to immediately check whether the selected configuration fits into one‘s own design. This aspect is all the more valuable for time-critical tasks. More information on Ganter standard parts can be found on the internet at www.ganternorm.com
Securely Fastened Loads
When something needs to be lifted, a crane, ropes or chains are needed – plus anchoring points on the load itself. Ganter offers a wide range of solutions here. The classic and simplest lifting points are lifting eye bolts according to DIN 580, which are screwed into existing threads on the load. When threads are not possible, lifting eye nuts according to DIN 582 are used instead. Ganter offers these standard parts in two materials: steel and stainless steel. However, a look in the Ganter portfolio reveals far better and stronger lifting points that are optimized for specific materials and – most important – easier to handle. In particular, the integrated RFID tags are worth mentioning as a special highlight. These make it possible to clearly identify specific lifting points during wear and safety inspections and manage them digitally and without system interruption. Such RFID tags can be found in the lifting eye bolt GN 581 and the lifting eye nut GN 583, for example, which are still able to rotate around their vertical axis even after installation. Both of these options also identify load rings GN 586.1, although here the lifting eye can also be folded down. And thanks to the eye ring with ball bearing, load rings GN 5860 are fully rotatable even under load. Load rings GN 587.1 are not screwed in but welded on. This load ring is also suitable for outdoor applications since the design of the weld-on block permits a closed seam that is safe from corrosion. The ring itself can be swiveled by 180 degrees, and an optionally integrated spring can secure it in any position. The lifting point GN 589 for welding can accept loads from any direction and impresses with its minimal height. This is an extremely important feature when the maximum hook height of the lifting equipment is limited.
Aluminum Profile Systems Designed for User-Friendliness
Ganter has long offered an extensive range of accessories for building machines, systems or workstations with standard profile systems. The aluminum profiles themselves have now also been added, along with the associated connecting parts. Ganter always thinks in terms of applications – that is the great strength of the market leader in standard parts. The same is true for the newest additions to the product portfolio: system-based aluminum profiles. The anodized, extruded profiles match the dimensions and properties of the longstanding systems of Bosch and Item, with heavy and light versions, a variety of cross-sections, dimensions and slot arrangements. For some time, Ganter’s product range has included many key elements for the custom use of profile systems. These include diverse angle brackets, T-nuts and everything else for attaching parts directly and indirectly to modular profile constructions: U-handles, hinges, panel support clamps and leveling feet, just to list a few examples. Now the profiles themselves are included, as are specific connecting elements and other parts, such as cover and edging profiles, end caps, joints and foot plates. Thanks to these additions, it is now possible to build entire fixtures, machines, systems or workstations with Ganter parts – with no need to order additional parts from other suppliers, making procurement simpler and more efficient.
Precision Hinges
New Hinge Generation for Precise Movements The new precision hinges from Ganter – available in many different versions – are wear resistant while delivering extreme precision and exhibiting zero backlash. Certain applications, such as in jig construction, automation systems or testing systems, require moving elements supported by extremely precise bearings. In concrete terms, this means a combination of maximum repeatability, zero backlash, long service life and adjustability. These are exactly the properties of the new precision hinges GN 7580, which might be more accurately referred to as joints. Of course, the Ganter portfolio already contains many different hinge versions, but these new products are generally suited to a unique range of applications. Facing increased demand for extremely precise pivot bearings, Ganter decided to design optimal solutions to fill this gap. The GN 7580 family consists of three size variants, each with four inner and outer leaf types. The leaves differ in turn by the type of mounting, which can be tangential or radial and make use of countersunk cylindrical bores or integrated threaded bushings of stainless steel. Plus, Ganter put thought into ensuring simple and positionally accurate mounting: The fitting bores ensure exact positioning of the hinges during installation. The four leaf types are designed to be mutually compatible and can be used together as needed in any combination. As usual with Ganter, they can even be ordered separately via specific article numbers. This ensures that the precision hinges cover a very wide range of applications. In general, Ganter supplies the precision hinges pre-assembled according to the customer-specific configuration. More information on Ganter standard parts can be found on the internet at ganternorm.com
Smart Pneumatic Indexing Plungers
Ganter is expanding its range of indexing plungers with a technical treat. The newest addition, type GN 817.7, is pneumatically actuated and can be seamlessly integrated into automated processes thanks to state-of-the-art sensors. There aren’t actually any indexing plunger variants lacking from Ganter’s portfolio. Nevertheless, the development team consistently succeeds in integrating new functionality that opens up new application possibilities. The most recent indexing plunger development is pneumatically actuated. Plus, the part also detects both end positions with just a single sensor. This makes GN 817.7 a logical advancement over the manually operated indexing plunger GN 817.6. The new variant can also be used in hard-to-reach locations and can be integrated into automated processes. What’s more, GN 817.7 can be used as a replacement for GN 817.6 without any changes in dimensioning or signal processing. The position detection of GN 817.7 is once again based on proven magnet technology but with some important new innovations. Not only are both end positions now detected but they can also be individually defined. The sensor teaching can be performed directly on-site with a small operating element on the sensor, which is held in place by a clip and supported by a cable. There are even LEDs for visual feedback. The other option for teaching is to use the convenient IO-Link feature via the system control unit. This standardized interface makes teaching a quick affair and also allows for immediate replacement in the case of faults, which significantly reduces downtime. The high signals upon reaching the respective end positions are transmitted directly over the 4-pin M8 cable plug to the control unit of the system. More information on Ganter standard parts can be found on the internet at www.ganternorm.com
New Product Roll-Out
Ganter is expanding its portfolio with a new product family: a selection of various casters and wheels.
News
Indexing Plungers with Special Tips
Indexing Plunger Tips for Special Requirements
A New Take on Indexing Plungers
Indexing plungers can be found practically everywhere. And Ganter has them in every shape, size and type.
Cable Glands and Accessories for Every Area of Application
Wherever cables or lines are run through an enclosure wall, strain relief and sealing are required. Ganter now offers the right cable glands and accessories in three thread types.